Precision Trak & Stop Kit

Average Review (3):

Take the guesswork out of cutting wood to length.

  • Turn your miter saw into a precise cutting system
  • Adjustable stops position your workpiece for repeatable, reliable results
  • Precision Lens Cursor for fast, accurate positioning
  • Production Stop and Swing Stop provide great results
  • L-shaped base design makes alignment and mounting easy
  • Includes 8' (2438mm) of Trak in 2' (610mm) long sections that can be used on the right or left side of the saw, or split between both sides
  • 2 self-adhesive measuring tapes correctly measure cut lengths on both sides of the blade


ITEM#: KMS8000

Add to Cart


Take the guesswork—and your tape measure and pencil—out of cutting wood to length. Our Precision Trak and Stop Kit allows you to turn a miter saw into a precise cutting system. Simply position the stop at the dimensions you'd like to cut using the precision lens cursor, place the board against the stop, and cut to that exact length every time. You build the support wings out of plywood (or another sheet material), and then add the Trak. Outfitting your saw to cut perfectly-sized workpieces couldn’t be simpler!

Perfect for a Variety of Applications
The most common setup for the Precision Trak & Stop Kit is with a miter saw, but many woodworkers find it handy to add to their radial arm saw or drill press. No matter where you use the Precision Trak & Stop Kit, you’ll find it much faster and accurate than any other wood-cutting method.

Production Stop
Designed to stand up to the rigors of repetitive cuts in an industrial environment, the Production Stop drops onto the top of the fence and features dual lens cursors for convenient use on either side of the blade.

Swing Stop
The Swing Stop gives you a precise measurement when you need it and swings out of the way when you don’t Simply push a board into the curved face of the stop to push it temporarily up out of the way, or swing the stop up. Like the Production Stop, it features a Precision Lens Cursor for fast, pinpoint positioning.

Shop-Made Support Wings
Build a simple plywood or MDF box to match the height of your saw, and then add a back fence that reaches 21/4" (57mm) above the saw table for the stops to glide upon. Instructions and mounting hardware for the Trak are included.

Rigid Aluminum Fence
Incredibly strong and built-to-last, our anodized-aluminum Trak features an L-shaped base that makes alignment and mounting to any 3/4" (19mm) thick board a snap. The Trak has a groove along the top to accept the included self-adhesive measuring tapes. The Trak is split into four 2' (610mm) long sections, giving you setup options: 4' (1219mm) on each side of the saw, 2' (610mm) on one side and 6’ (1829mm) on the other, or all 8' (2438mm) on one side.

California Residents: Prop 65 Information



Aircraft-grade aluminum


Anodized for easy clean-up

Cutting Capacity

96" (2438mm) minimum


(4) 2' (610mm) sections for 8' (2438mm) of Trak length

Measuring Tape

(1) 12' (3658mm) left-to-right reading
(1) 12' (3658mm) right-to-left reading


(4) 2' (610mm) pieces of Top Trak, Swing Stop, Production Stop, 12' (3657mm) L-to-R reading self-adhesive tape, (1) 12' (3657mm) R-to-L reading self-adhesive tape, and owner's manual


Proposition 65

Manual North American Manual

Reviews for "Precision Trak & Stop Kit"

Average Review:

Same as above - great tool but no metric/imperial combo tape?

Very frustrating. I use both regularly. The stops are fantastic BUT I wish they both had a small opening to allow sawdust to escape rather than building up in the corner between the stop and the fence. Because there is not an escape hatch the dust buildup causes your cuts to be off after just a few boards and the problem grows worse and worse until you remember to blow out the dust stuck in the corner.


By Patrick Nickles

February 20, 2019

Excellent product but no option for metric tape...

I used this stop lots when I worked in a wood shop in the USA liked it so I bought one for the shop I’m setting up in Brazil, but there is absolutely no option for a metric(which almost everyone besides the USA uses) tape for the track. Couldn’t even find a 1/2” flat metric tape from a third party. So I have to buy a 3/4” wide tape and somehow cut it to width. It’s disappointing such a VERY SIMPLE conversion between metric/inches is not available for such a nice jig/track.


By Michael Goossen

November 9, 2017

Good production cutting

I have had this set up to one side of my radial arm saw for a number of years now and love it with only a couple of problems. I just recently contacted Kreg with the news that the plastic screw which holds the adjustable lens had the head break off making it so I could not adjust the guage. To Kreg's credit they have returned my correspondence and have volunteered to replace the screw. The other problem that I have is that the measuring tape on the t rack has buckled up over the years for some reason which throws off the calibration of the stops when set up on one side of the buble and move to the other. I do see that they have replacement tapes and have contacted them in terms of getting a replacement. These seem to be very reasonably priced. All in all, I have several Kreg Jigs for building cabinets and have been pleased with all.


By Phil Cutting

July 20, 2015

This website uses first party and third party cookies to improve your experience and anonymously track site visits. By visiting this website, you opt-in to the use of cookies. OK