Average Review (23):

Straight, accurate, splinter-free cuts made easy

  • Rip, cross cut, and make angled cuts up to 50" long in plywood, MDF, and panels
  • Simply align the Guide Track with your marks to make accurate cuts
  • Hold track in place without clamps thanks to anti-slip guide strips
  • Prevent splintering with anti-chip strips that support material during the cut
  • Begin cuts easily with a Starting Block that supports the saw and allows normal blade guard operation
  • Mount almost any circular saw—left or right blade—to the Universal Sled
  • Universal Sled is compatible with the Kreg Rip-Cut™
  • Take your saw to the material instead of having to take your material to the saw
  • See a video on how-to break down large panels with the Accu-Cut and the Rip-Cut


ITEM#: KMA2700

Add to Cart


Transform your circular saw into a high-performance, track-guided cutting tool

Start projects right by making straight, accurate, splinter-free cuts with your circular saw and the Accu-Cut™ Circular Saw Track Guide. It rips, crosscuts and makes angled cuts up to 50" long in plywood, MDF, and other large panels with super simple setup, precise accuracy, and amazing control.

The Accu-Cut guides your circular saw along an aluminum track that keeps the saw moving in a straight line easily. The Accu-Cut™ design makes it simple to set up by just aligning the track with your cut line. No clamps are required to hold the track in place thanks to dual guide strips. They feature an anti-slip coating to prevent slipping, and an anti-chip feature to prevent splintered cuts. Plus, the track makes it easy to make straight cuts on sheets that don't have a straight, flat edge.

Circular saws don’t have effective guides that keep them moving straight along a cut line. Plus, it can be difficult to see the blade’s cutting path. Together, these things make it challenging to keep a saw on your desired cut. Circular saws also often cause splintering of face veneers. The Accu-Cut™ solves these problems. The Accu-Cut™ is portable, too, so you can take your saw to the workpiece and cut with precision, rather than having to handle heavy sheets on a table saw. 

The Accu-Cut™ is easy and intuitive for a novice to use, but robust enough for professionals. Because it eliminates the need to keep the saw straight and manually guide the saw along a cut line, the Accu-Cut™ is ideal for less-experienced users. Accu-Cut™ also makes professionals faster and more productive because it makes a variety of cuts quickly and easily in the shop and on the job site.

Accu-Cut & Rip-Cut - Breaking down the difference

How-to break down large panels with the Accu-Cut™ and the Rip-Cut™

Using the Accu-Cut sled on the Rip-Cut

How to use the Accu-Cut™ Universal Sled with the Rip-Cut™


Guide Track

Aircraft-quality aluminum with dual anti-chip, anti-slip guide strips 

Saw Sled

Accepts left- and right-blade saws
Built-in indexing stop and precision cursor

Cut Length

Maximum 50" (1270mm)


(1) Universal Saw Sled, (2) 26.5" Aluminum Guide Tracks, (2) Track Connectors, (1) Starting Block, (1) Track Indicator Clip, detailed setup and usage instructions


Proposition 65

Manual North American Manual

Reviews for "Accu-Cut™"

Average Review:

Does the job

I used to use a piece of 1x3 (various lengths) clamped to plywood for the rip and crosscuts, but the Accu-Cut does it better than the way I used to do it. It is sturdy (stays in place), accurate, and easy to configure for my Milwaukee circular saw.


By Alan Borack

June 28, 2019

Too much slop between track and saw.

I’ve tried to use the accu-cut several times. I have been disappointed with the results. While setting up the saw I noticed the track and plate were not a snug fit. This slop allows the saw to cut a quite crooked line. To combat this I would have to hold the saw tight against one side or the other of the track by pushing sideways to follow only one side of the track. However, this would cause the blade to contact the rubber edge or blade to not line up with the edge. This also caused the track to bind and to slip on the material. I’m sure this tool is better than freehanding a long cut. However, it cost way more than it should for the lack of precision.i purchased the track for a project but had to abandon my plans to use it due to poor performance. I therefore had to make all my cuts the old fashioned way. A trim board and two clamps. This worked way better and was pretty much free.


By Jason Hall

May 6, 2019

Very accurate

I found this product to be very accurate and it works perfectly with my Makita cordless circular saw. Would love to see more track sold separately.


By Alan Reddick

January 29, 2019

Enables Precision Cuts

Purchased Rip Cut first. Liked it. Saw a need and use for the Accu Cut. I am a DIY in the strictest sense of the term. I don't have a shop. I work in my garage. I share it with my wife's car and all the other "stuff" that is in there. I lay my materials out on the floor to cut them. I was ok if there was a little wobble in the cut lines or if the measurements were slightly off every now and then. Just part of the deal, ya know? I set the Accu Cut up as per the directions and it made a straight cut on the mark the first time. I swap my saw, in the sled, between the Rip Cut and the Accu Cut and I make precision cuts every time. The only thing I can comment on that might be construed as negative is the set screws where the track joins tends to loosen when moving the track around. Thought about Loctite but want to be able to take it apart to store in tool cabinet so I just periodically check them for tightness. Accu Cut has definitely made DIY projects easier with better end results for me.


By David Bankston

November 26, 2018


II purchased the Accu-cut in November 2017 and have used it a number of times in my workshop. Generally it is a useful addition to the shop, however, I have experienced some disappointing difficulties in its use. Firstly when attaching the base slide unit to my 91/4" Triton circular saw I am unable to use the stop block which is essential to the quick removal and replacement of the saw. The Triton's base plate is about 1/4" too wide to allow the positioning of the stop block. This is not a major issue for me and I am able to switch the saw in and out with a minimum of fuss it just took a bit of thought and effort to get it right the first time. The Major limitation for me is the lack of clamping mechanisms to fix the track to the material to be cut. I have no problems with plywood but the track continues to slip and slide when used on MDF. I have certainly ensured that the black rubber backing on the track and the MDF are clean of all sawdust etc and have even resorted to vacuuming the MDF and the track but to no avail it continues to move of the line . I hope that your design engineers can eventually fix this issue and manufacture something thatn can be retrofitted to the accu-cut slide. I am more than satisfied with the many other Kreg tool, and jigs and will continue to purchase your products as and when required. Regards, Richard Monk


By Richard Monk

November 20, 2018

Read more reviews

Get Inspired