Reviews for "Crown-Pro™"

Kreg Crown Pro cutting better

When Using the Kreg Crown Pro why is everyone still turning the crown upside down, If you turn the jig around facing the fence then you can cut the crown molding as it will go on the wall still set your spring angle. Left inside, jig to left blade to left, for right inside blade right material right, Left outside material to Left, blade to right for right outside, material to right blade to left that's laying your material facing you with jig turned the opposite to fence


Thomas Dicker

June 11, 2020

Not all that great

Although I was able to get good clean angles with this jig, I did have some issues with it. The little shelf under the molding is not wide enough, and allowed the workpiece to slide off. I really had to concentrate on lining it up horizontally, because the molding wouldn’t sit on the jig. The other big issue is that multiple times I had the cut-off piece kick out the back of the saw really hard. Pretty dangerous, and I’m glad there weren’t any windows or people in that direction. I think this is caused by the jig holding the workpiece above the saw table, with no support for the cut off section.


Jeremy Marshall

June 2, 2019

I love this product. saved me a lot of money by doing my molding myself

I was prepared to pay I figured about 2 grand to have someone install crown molding in my house. but after watching videos on you tube, and reading about this jig, I ended up buying a dewalt t milter saw on Black Friday, 12 inch blade, and ordered the crown-pro. after practicing on a few scrap pieces of crown, I stated to cut and install. I only did inside cuts for one room, and the crown-pro made it very easy to cut inside corners. I dont normally do fanatic work on my home projects, but the crown pro made the job very easy, and the first room I installed crown molding came out great. going to do the whole house and save a lot of money. love my crown-pro


dave paul

December 7, 2017

Underneath Red setting

The red setting gauge underneath the unit should be a medal guide with black degree markings. It would set much more precisely with this design. Also it would make the spring angle setting easier in the instruction manual to state "use the vertical side of the pointer to the angle desired". The slope side shows 40 in the illustration which can be misleading. The manual picture shows such but words would also help the novice.


James Jackson

November 29, 2017

Needs robustness

The jig suffers from distortion when pressure is place on one end or another to hold the stock in place. During installation of 1600 feet of molding we found first that the angle adjustment had slipped (perhaps not tightened enough), but then after marking the seating on each end to watch for slippage, we discovered that one end had twisted. The lower lip was also flexible, and for our molding it would have been nice to be a bit deeper. Finally, it would be nice to have cork or rubber on the face to help steady the stock. We'll continue to use it with the above precautions, but a second, more robust version should be planned. For a big job, we would use two jigs to avoid moving it back and forth from left to right side of the saw blade.


Frederick Grose

April 26, 2017

Awsome Product

We purchased this to put crown molding in the kitchen. After reading the manual, watching the product video, and watching the crown molding installation video with professional builder Gary Streigler we got our crown molding up first time no problems. If you do what I said above you will have no problems either. Someone said the manual did not say to cut the molding upside down (the most decorative side up) you are wrong and did not read the manual because it is in there.


Ron Bertke

July 4, 2016

Great tool that makes Coving a dream!

Coving a room has always been one of those tasks you either love or hate, I have tried many different jigs over the years and all have had some small amount of success, but this jig from the guys at Kreg is just a dream to use, it makes perfect cuts every time and the joints are never out, its so easy to use and makes an annoying job a joy to do, the only reason that I did not give it a full house with regards to stars is because the bottom lip of the jig is way too small for most of the coving that we have here in the UK, if this was just a cm or two larger it would be a perfect jig. Well worth the cost and well recommended...


James SawleJamesS

November 29, 2014

Love the Crown-Pro!!

I mangled 3 nice pieces of crown molding and, of course, suffered a berating from my wife for my effort....I guess the You tube videos didn't quite cut the mustard on this one. I purchased the Kreg Crown-Pro, received it in a couple of days and within a couple of hours had my crown molding cut and installed. The instruction booklet was clearly written on how to find the 'spring angle' on any crown molding using their angle finding tool and has clearly printed diagrams to show the position of the molding, and the miter saw, for each cut. The Crown-Pro is easy to set up and to use and is most definitely worth the price considering the cost of crown molding. Kelly Wunderlich, Bend, OR.


Kelly Wunderlich

July 22, 2014

This website uses first party and third party cookies to improve your experience and anonymously track site visits. By visiting this website, you opt-in to the use of cookies. OK